Johnsonite 996 Two Part Epoxy Adhesive
Johnsonite 996 two part epoxy adhesive is formulated for the installation of wheeled traffic transitions on surfaces where there are environmental and health concerns. Sold as a set - part a and part b. Gallon sized container of each.
- Shipping info
Website will only calculate shipping for the Contiguous US.
All other locations please call for shipping quote - 866-258-1554 - Payment methods
- Return Policy
We accept returns on many of our products. Please check the product page to make sure your items are not considered special order non-returnable as these are not accepted as returns.
Johnsonite 996 Two Part Epoxy
Johnsonite 996 two-part epoxy adhesive is formulated for the installation of wheeled traffic transitions on surfaces where environmental and health concerns require an adhesive with environmentally sensitive characteristics. This 2 part epoxy glue is solvent-free and contain no hazardous or carcinogenic ingredients as defined by OSHA, Federal or State Agencies. Purchasing the Johnsonite 996 two-part epoxy, you will receive 2 containers combined for .92 gallon: part "A" and part "B".
Johnsonite Two Part Epoxy Adhesive Highlights:
- Sold in 2 containers (Part A and Part B)
- 2 part epoxy glue is solvent-free and contains no hazardous ingredients
- Shelf Life - 1 year at 70 degrees when stored in unopened, original container in a dry area
- Open Time - maximum open time is 40 to 50 minutes at 75 degrees or higher
- Coverage approximately 150 square feet
- Can be used on porous or nonporous surfaces
- For interior use only
Lead time will depend on stock (typically 1-3 weeks). Please call for availability.
Johnsonite two part epoxy adhesive is recommended to use when installing:- Johnsonite Brand
- Wheeled Traffic Transitions
- Feature Strips*
This item is considered special order and not listed on our site. Please contact us for pricing and more information.
Product Specification Data Sheet for this product
Material Safety Data Sheet for this product
Johnsonite 996 Application Instructions for Wheeled Traffic Transitions:- Mix all of part "B" into part "A" and mix thoroughly until smooth and uniform in color
- Mix for another 3-5 minutes. Adhesive will not cure if not properly mixed
- Immediately after mixing, apply to substrate using a 1/16 inch square-notched trowel
- Carefully position and install the molding. Use a J-Roller and hand roll the molding to ensure proper adhesive bond
- Avoid traffic for at least 12 hours after installation
- Avoid cold or excessive heat, including direct sunlight during installation
Shipping Policy:
Available shipping options are shown in the table below.
| Shipping Type | Fee | Details |
| Standard Shipping | $7.99 | Order will be processed according to when submitted |
| Overnight | Please contact for rates and availability | 866.258.1554 608.244.1226 Sales@InstallerStore.com Monday - Friday 8am-~4:30pm CST |
| Two Day | Please contact for rates and availability | |
| Three Day Express | Please contact for rates and availability | |
| Outside Contiguous US | Please contact for rates |
Standard Shipping will ship out ground USPS, FedEx, UPS, or Spee-Dee Delivery.
Please call, toll free at (866) 258-1554 or our local number at (608)-244-1226, Monday through Friday, 8am-4:30pm CST or email for expedited, APO/FPO, or shipments outside Contiguous US. Please note customers are wholly responsible for these shipping fees.
Transit times can vary depending on destination. Orders are shipped Monday through Friday, with the exception of national holidays.
We accept the following payment methods:
You can also call us or mail in a check.
Payment must be made before items ship.
Return Policy:
Please contact us immediately in the event an incorrect product has been sent or an order has been damaged in shipping. We will gladly remedy the situation at no extra cost to you.
Acquiring a Return Merchandise Authorization (RMA) Number:
Please call 866-258-1554 or email Sales@InstallerStore.com to receive a Return Merchandise Authorization number if there is any reason you would like to return your order. All charges to ship merchandise back are the responsibility of the shipper. There will be a 10% re-stock fee on all returned orders, unless a replacement order has been made. Customers are given 7 days from the delivery date to contact us for a RMA number. Returns must be received back to our warehouse within 90 days. Fees may change based on extended time passing.
Returns of open/used products are not accepted.
**Special order items are not returnable and are designated on the specific product pages.**
Shipping charges are not refundable.
InstallerStore/Covebase-n-transitions strongly encourages choosing a shipping method for your return where a tracking number and insurance can be obtained. Accounts will be credited back after inspection has been made to the product to ensure product has not been damaged in any way and can be resold. Packages damaged while being shipped back to us will not be accepted as a return and customer will be contacted. InstallerStore is not responsible for lost or damaged returns. It is the customer's responsibility to file a claim with the shipping company.
Any merchandise that is shipped back without a RMA number will have a minimum re-stocking fee of 25% of the product cost and shipping charges will not be refunded.
All returned products must be shipped directly to InstallerStore even if they were originally shipped from the manufacturer, unless otherwise told by InstallerStore. Shipping back to manufacturer may cause re-stocking fee to increase.